Numark Orbit - Setup in Resolume VDJ Software

numark orbit mainThe Numark Orbit is a wireless MIDI controller that allows the control of any software that accepts general MIDI information. This guide covers loading a specific Resolume mapping file into the Numark Orbit and the Resolume Arena software. There are detailed steps to mapping the accelerometer to the desired video or audio effect.

 

Table of Contents

  1. Before We Begin
  2. Getting Started
  3. Configuring Resolume MIDI Settings
  4. Loading a Resolume Composition
  5. Orbit Mapping Explained
  6. Controlling Video Effects with Accelerometer
  7. Creating Custom MIDI Map
  8. Further Technical Assistance

 

Before We Begin

Download the necessary content for this tutorial here.

You can obtain the Resolume Demo software below:

 

Download Resolume
http://resolume.com/download/

 

Resolume Manual
http://resolume.com/support/manual/

 

 

 

 Getting Started

 

  1. Connect your Numark Orbit to your computer by plugging in the included USB dongle receiver and power on your Orbit.
     
  2. Open the Numark Editor. Click File then Open.

    numark orbit resolume01
     
  3. Choose the Numark Orbit Resolume mapping file. Click Open.

    numark orbit resolume02
     
  4. The preset mapping file is now loaded into the software. Click Send in the bottom of the Orbit Editor software. You should see file send success when completed.

    numark orbit resolume03
     
  5. Click File then Exit to close the software.

 

Configuring Resolume MIDI Settings

 

  1. Open the Resolume software.
     
  2. Choose Arena and then Preferences.

    numark orbit resolume05
     
  3. Select the MIDI tab. Turn on the MIDI Input of the Numark Orbit.

    numark orbit resolume06
     
  4. Look at the bottom of this window. Click Load.

    numark orbit resolume07
     
  5. Choose the ResolumeOrbitMapping file provided in this tutorial. Click Open.

    numark orbit resolume09
     
  6. Once this is completed, click the Red X to close the window.

 

 

 

Loading a Resolume Composition

 

  1. Choose Composition and then Open.

    numark orbit resolume12
     
  2. Choose your Compositions folder.

    numark orbit resolume10
     
  3. Select the premade Resolume Orbit composition included with this tutorial.

    numark orbit resolume11

 

 

 

Orbit Mapping Explained
 

 

  1. Yellow - Selects Columns 1-6
  2. Green - Engage Track 1-3
  3. Orange - Mute Track
  4. Purple - Tap Tempo -
  5. White - Half/Double Tempo
  6. Red - Record
  7. Kontrol Wheel  - CrossFader

    numark orbit resolume36
     

 

 

 

  1. Select Column 1 by pressing the first yellow pad. There are 9 yellow pads for each of the 9 columns.

    numark orbit resolume14
     
  2. The three Green pads indicate Layers 1 - 3. Select a layer by pressing the associated pad.

    numark orbit resolume15
     
  3. The Purple pad is assigned to Tap Tempo. This allows the syncing of effects to the BPM of a an external audio source. The White LEDs will cut in half or double the BPM.

    numark orbit resolume16
     
  4. The Red pad initiates the record mode. When you are finished recording your video, press the Red pad again to stop the recording.

    numark orbit resolume17

    numark orbit resolume19
     
  5. The Left and Right accelerometer is assigned to color effects in this project. See "Creating Custom MIDI Map" to assign new desired parameters to the Orbit's accelerometer.
     
  6. The center Kontrol Wheel is used to control the crossfader. All clips can be designated to be on Deck A or B or both

     numark orbit resolume21

 

 

 

 Controlling Video Effects with the Accelerometer 

 

  1. Using the Numark Orbit, press the first Yellow pad to launch Column 1. This loads all clips in column 1 into the output display.
     
  2. Press the 2nd Green pad to select Layer 2.
     
  3. Use the Left or Right accelerometer triggers to control the assigned video effects.

    numark orbit resolume24
     
  4. Select the 1st Green pad to select Layer 1. You now have control of that layers video effects when using the left and right accelerometer buttons.
     
  5. Try launching clips from Column 2 and so on.

 

 

 

Using the Tap Tempo

 

  1. Right Click to the left of a parameter. Choose BPM Sync.

    numark orbit resolume34
     
  2. Using the Purple Pad on your Orbit, Tap the tempo of the song. The effect will now be synced to the tempo of the music.

 

 

 

Creating Custom MIDI Map

 

  1. Select Arena from the toolbar, and then click Preferences.
     
  2. Select the MIDI tab. Choose New. Name your new MIDI Map and then click Save.

    numark orbit resolume25

    numark orbit resolume26
     
  3. Select Mapping from the upper toolbar. Choose Edit Application MIDI Map.

    numark orbit resolume28
     
  4. All mappable parameters are displayed in yellow. With your mouse, click on a parameter.

    numark orbit resolume29
     
  5. Press the left or right accelerometer. You will see that control value displayed in the yellow area. It is also recommended to use the Kontrol Wheel for effects.

    numark orbit resolume30
     
  6. Continue to do this with as many different parameters you like. The fun is experimenting with how effects interact with each other.
     
  7. When this is complete, select the Mapping tab from the upper toolbar. Select Edit Application MIDI Map to disengage MIDI mapping.

    numark orbit resolume31

 

 

 

Warranty Information and Technical Support

 

Whether you are a customer or dealer, if you already own a Numark product, or if you just have pre-sales questions, the Numark technical support team is available to help!

 

Visit the link below to connect with any of the following support options: online community support, phone support, email support.

 

Numark Support Contact